Subject | Text |
| PS42V6 is a plasma tv, fault could be lower scan pcb or connectors to pdp, or a bad pdp |
| Check the resistor on the flat cable from PCB to PDP module. When is resistor broken try change it. |
|
Job | Hi, my name is vik.I am 18 years experience in repairing these eqiupment(tvs,vcr,hi-fiandsoon).i hav |
| hope you are transfered to correct section.
If you have the power into set, locate where there is 9 |
| Thank You Gest.
I am working on a Sony KP-51HW40 Projection TV.
When I power up the TV there are a |
not that fault | hi i tried that but not fixed it, sometimes if i keep turning tv on and of and on and off it will co |
| I am going to be quite honest and to the point here.
If one doesn't at least understand Ohm's Law |
Deskjet 9650 - blinking resume light | There isn't a print jam or a job pending to print. This printer isn't attached to a PC. Once it pr |
Where to look in a CRT monitor for a "ghosting" pr | I'm just an electronics hobbyist,not a service tech. Can anyone tell me where I should start trouble |
goodmans gtv42p | I require a service manual for goodmans gtv42p it uses a samsung S42D-YD05 pdp panel thanks gary |
Need help with testing TV components | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points to |
| Welcome to plasma's. Seems with x/y disconnected VS and Va are ok indicating a good power supply. Ho |
| i hAve sony service and training manuals
2000-2006
excellent for any shop
[email protected] |
| Thanks PBS Engineer - I've had a look and have stopped drooling now!
I joined the BBC in London i |
Manual please! Whirlpool solutions adp755 dishwasher | I have been given an old Whirlpool solutions adp755 dishwasher, but it has come without a manual. I |
Re: Worked for me also. Great Job | [quote:33bb56492b="Damanvir"]Agatha,
Great Job my camera works well. After reading previous strin |
hcn4727w red blink | similar to http://forum.eserviceinfo.com/viewtopic.php?t=23895&start=20&postdays=0&posto |
|
| The relay is doing what it's supposed to do and is not your problem. This could be:
(1) a solder ( |
help on sharp 14v-s100 | hello! i need help with my 14" sharp 14v-s100. first it doesn't turn on. the led the supposed |
NEC RD-317, PX-RC1E | Hello !
I am looking for programming manuals RD-317, lcd remote controller for NEC PDP monitors. |
Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| [quote:6ce24b5b34="jts1957"]I usually just take a magic marker and draw a line across the control - |
| Thanks. I was nerves, this was the first time I have ever opened a monitor up and messed around insi |
| Hi Minnnie,
Thanks much for the quick reply. I looked around inside the set and didn't and didn't |
is this southbridge problem...! | Fujitsu siemens amilo m-7405 laptop have problem... i connect my mobile with usb port and then sudde |
Re: looking for service manual epson epl-6200 | [quote:9834da5eeb="karlevis"]My printer flashing and not pick-up the paper, anyone knows this troubl |
| I am able to program the remote to work with my cable box...and thanks for the advise, I will try th |
| [quote:0e72665aba="thetimewizard"]I own a clock shop and I repair and restore old clocks for a livin |
LG Flatron MZ-42PZ24-After turning it on,it turns to standby | Hello,
i hope someome can help me with this problem on my LG PDP Plasma TV:
When you turn it o |
Looking for a couple of Plasma TV boards | I'm trying to fix my plasma and need the following boards to do so:
SDBD 6871QDH067B
YSUS 6871 |